597d www.vishay.com vishay sprague revision: 25-jun-13 1 document number: 40047 for technical questions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 solid tantalum chip capacitors, t antamount ? , ultra-low esr, conformal coated, maximum cv performance characteristics www.vishay.com/doc?40088 operating temperature: - 55 c to + 125 c ? (above 85 c, voltage derating is required) capacitance range: 10 f to 1500 f capacitance tolerance: 10 %, 20 % standard voltage rating: 4 v dc to 75 v dc features ? new case si ze offerings ? terminations: 100 % tin (2) standard; tin/lead available ? extremely low esr ? mounting: surface mount ? ripple current up to 4.1 a ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 note ? * this datasheet provides information about parts that are ? rohs-compliant and/or parts th at are non-rohs-compliant. for ? example, parts with lead (pb) te rminations are not rohs-compliant. ? please see the information/tables in this datasheet for details. note ? preferred tolerance and reel sizes are in bold. ? we reserve the right to supply higher voltage ratings and tighter capacitance tolerance capacitors in the same case size. ? low esr solid tantalum chip capacitors allow delta esr of 1.25 time s the datasheet limi ts after mounting. note ? the anode termination (d less b) will be a minimum of 0.012" [0.3 mm] available available ordering information 597d 687 x0 6r3 e 2 t type capacitance capacitance tolerance dc voltage rating at + 85 c case code termination reel size and packaging this is expressed in pf. the first two digits are the significant figures. the third is the number of zeros to follow. x0 = 20 % x9 = 10 % this is expressed in v. to complete th e three-digit block, zeros precede the voltage rating. a decimal point is indicated by an r (6r3 = 6.3 v). see ratings and case codes table 2 = 100 % tin 8 = solder plated (60/40) special order t = tape and reel 7" [178 mm] reel dimensions in inches [millimeters] case code l (max.) w h a b d (ref.) j (max.) v 0.299 [7.6] 0.173 0.016 [4.4 0.4] 0.079 [2.0 max.] 0.051 0.012 [1.3 0.3] 0.181 0.024 [4.6 0.6] 0.252 [6.4] 0.004 [0.1] d 0.299 [7.6] 0.173 0.016 [4.4 0.4] 0.138 [3.5 max.] 0.051 0.012 [1.3 0.3] 0.181 0.024 [4.6 0.6] 0.252 [6.4] 0.004 [0.1] e 0.299 [7.6] 0.173 0.016 [4.4 0.4] 0.157 0.016 [4.0 0.4] 0.051 0.012 [1.3 0.3] 0.181 0.024 [4.6 0.6] 0.252 [6.4] 0.004 [0.1] r 0.299 [7.6] 0.238 0.016 [6.0 0.4] 0.142 0.016 [3.6 0.4] 0.051 0.012 [1.3 0.3] 0.181 0.024 [4.6 0.6] 0.244 [6.2] 0.004 [0.1] f 0.299 [7.6] 0.238 0.016 [6.0 0.4] 0.185 0.016 [4.7 0.4] 0.055 0.016 [1.4 0.4] 0.181 0.024 [4.6 0.6] 0.244 [6.2] 0.004 [0.1] z 0.299 [7.6] 0.238 0.016 [6.0 0.4] 0.236 0.016 [6.0 0.4] 0.055 0.016 [1.4 0.4] 0.181 0.024 [4.6 0.6] 0.244 [6.2] 0.004 [0.1] m 0.315 [8.0] 0.260 + 0.016/- 0.024 [6.6 + 0.4/- 0.6] 0.142 0.016 [3.6 0.4] 0.051 0.012 [1.3 0.3] 0.197 0.024 [5.0 0.6] 0.260 [6.6] 0.004 [0.1] h 0.315 [8.0] 0.260 + 0.016/- 0.024 [6.6 + 0.4/- 0.6] 0.205 0.016 [5.2 0.4] 0.055 0.016 [1.4 0.4] 0.197 0.024 [5.0 0.6] 0.260 [6.6] 0.004 [0.1] j h b a d l tantalum wire nib identifie s anode (+) terminal w
597d www.vishay.com vishay sprague revision: 25-jun-13 2 document number: 40047 for technical questions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 ratings and case codes f 4 v 6.3 v 10 v 16 v 20 v 25 v 35 v 50 v 63 v 75 v 10 dr 15 e/r r 22 rf 33 f 47 rz 68 rf 100 ff 150 f 220 e r m 330 v e f h 470 v e e h 680 e e r 1000 e/r r f 1500 r 2200 standard ratings capacitance (f) case code part number max. dcl at + 25 c (a) max. df at + 25 c 120 hz (%) max. esr at + 25 c 100 khz (m ? ) max. ripple 100 khz i rms (a) 4 v dc at + 85 c; 2.7 v dc at + 125 c 470 v 597d477(1)004v(2)(3) 19 8 60 2.2 680 e 597d687(1)004e(2)(3) 27 6 25 2.9 1000 e 597d108(1)004e(2)(3) 40 8 20 3.3 1000 r 597d108(1)004r(2)(3) 40 8 18 3.7 1500 r 597d158(1)004r(2)(3) 60 8 24 2.9 6.3 v dc at + 85 c; 4 v dc at + 125 c 330 v 597d337(1)6r3v(2)(3) 21 8 56 2.0 470 e 597d477(1)6r3e(2)(3) 30 6 30 2.7 680 e 597d687(1)6r3e(2)(3) 43 6 25 2.9 1000 r 597d108(1)6r3r(2)(3) 63 8 31 2.8 10 v dc at + 85 c; 7 v dc at + 125 c 330 e 597d337(1)010e(2)(3) 33 6 35 2.5 470 e 597d477(1)010e(2)(3) 47 6 28 2.8 680 r 597d687(1)010r(2)(3) 68 6 28 3.0 1000 f 597d108(1)010f(2)(3) 100 20 120 1.4 16 v dc at + 85 c; 10 v dc at + 125 c 220 e 597d227(1)016e(2)(3) 35 8 60 2.3 330 f 597d337(1)016f(2)(3) 53 10 100 1.6 470 h 597d477(1)016h(2)(3) 75 14 100 1.4 20 v dc at + 85 c; 13 v dc at + 125 c 220 r 597d227(1)020r(2)(3) 44 8 80 1.8 330 h 597d337(1)020h(2)(3) 66 10 100 1.6 25 v dc at + 85 c; 17 v dc at + 125 c 68 r 597d686(1)025r(2)(3) 17 6 100 1.6 100 f 597d107(1)025f(2)(3) 25 8 100 1.6 note ? part number definitions: (1) tolerance: for 10 % tolera nce, specify x9, for 20 % tolerance, change to x0 (2) termination: for 100 % tin specify 2 , for solder plated 60/40 specify 8 (3) packaging code: for 7" reels specify t
597d www.vishay.com vishay sprague revision: 25-jun-13 3 document number: 40047 for technical questions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 25 v dc at + 85 c; 17 v dc at + 125 c 150 f 597d157(1)025f(2)(3) 38 8 80 1.8 220 m 597d227(1)025m(2)(3) 55 8 100 1.6 35 v dc at + 85 c; 23 v dc at + 125 c 47 r 597d476(1)035r(2)(3) 17 6 100 1.6 68 f 597d686(1)035f(2)(3) 24 6 100 1.6 100 f 597d107x0035f(2)(3) 35 8 100 1.6 50 v dc at + 85 c; 33 v dc at + 125 c 15 e 597d156(1)050e(2)(3) 8 6 300 0.9 15 r 597d156(1)050r(2)(3) 8 6 250 1.0 22 r 597d226(1)050r(2)(3) 11 6 220 1.1 33 f 597d336(1)050f(2)(3) 17 6 150 1.3 47 z 597d476(1)050z(2)(3) 24 6 240 1.1 63 v dc at + 85 c; 42 v dc at + 125 c 10 d 597d106(1)063d(2)(3) 10 6 400 0.6 15 r 597d156(1)063r(2)(3) 10 6 400 0.8 22 f 597d226(1)063f(2)(3) 14 6 250 1.0 75 v dc at + 85 c; 50 v dc at + 125 c 10 r 597d106(1)075r(2)(3) 8 6 500 0.7 recommended voltage de rating guidelines (for temperature below + 85 c) standard conditions. for example: output filters capacitor voltage rating operating voltage 4.0 2.5 6.3 3.6 10 6.0 16 10 20 12 25 15 35 24 50 28 63 37.8 75 45 severe conditions. for example: input filters capacitor voltage rating operating voltage 4.0 2.5 6.3 3.3 10 5.0 16 8.0 20 10 25 12 35 15 50 24 63 32 75 37 standard ratings capacitance (f) case code part number max. dcl at + 25 c (a) max. df at + 25 c 120 hz (%) max. esr at + 25 c 100 khz (m ? ) max. ripple 100 khz i rms (a) note ? part number definitions: (1) tolerance: for 10 % tolera nce, specify x9, for 20 % tolerance, change to x0 (2) termination: for 100 % tin specify 2 , for solder plated 60/40 specify 8 (3) packaging code: for 7" reels specify t
597d www.vishay.com vishay sprague revision: 25-jun-13 4 document number: 40047 for technical questions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 typical curves 100 hz 1 khz 10 khz 100 khz 1 mhz 0.01 0.1 1 frequency esr and z ( ? ) 1500 f - 4 v r case size esr and z vs. frequency esr z 0.01 0.1 1 fre q uency e s r z 100 hz 1 khz 10 khz 100 khz 1 mhz e s r and z ( ) 330 f - 10 v e ca s e s ize e s r and z v s . fre q uency 100 hz 1 khz 10 khz 100 khz 1 mhz frequency esr z 0.01 0.1 1 10 esr and z ( ? ) 330 f - 6.3 v v case size and z vs. frequency 0.01 0.1 1 frequency esr z 100 hz 1 khz 10 khz 100 khz 1 mhz esr and z ( ? ) 1000 f - 6.3 v r case size esr and z vs. frequency 0.01 0.1 1 fre q uency 100 hz 1 khz 10 khz 100 khz 1 mhz 10 e s r z e s r and z ( ) 470 f - 4 v v ca s e s ize e s r and z v s . fre q uency
597d www.vishay.com vishay sprague revision: 25-jun-13 5 document number: 40047 for technical questions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 power dissipation case code maximum permissible power dissipation at + 25 c (w) in free air v 0.141 d 0.215 e 0.240 r, f, m 0.250 z 0.265 h 0.265 standard packaging quantity case code units per 7" reel v 1000 d 400 e 500 r 300 f 250 z 250 m 200 h 200 product information conformal coated guide www.vishay.com/doc?40150 pad dimensions packaging dimensions moisture sensitivity www.vishay.com/doc?40135 selector guides solid tantalum selector guide www.vishay.com/doc?49053 faq frequently asked questions www.vishay.com/doc?40110
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
|
